############
air sns NANO
############

The DST air sns NANO is a commercial indoor air quality monitor with a LED matrix display.

Specifications
==============

* Power: AC 100-240V to DC 24V power adapter
* Connectivity: WiFi / Ethernet / Modbus via RS-485 / NB-IoT

Measurement Fields
------------------

* PM2.5
* PM10
* TVOC
* HCHO
* CO
* CO2
* NO2
* Temperature
* Relative humidity
* Air pressure
* Light
* Noise

Configuration
=============

To access the configuration page of the monitor, follow the steps below:

#. Power up the monitor
#. Use a sharp pin to press and hold the "Configuration" button inside the pinhole for at least 6 seconds

.. image:: /images/dst/nano_config.png

#. Connect a computer or a smart phone to the wireless hotspot created by the monitor; its SSID (network name) should
   start with *NANO* or *MXCHIP*
#. On the web browser of your device, type *10.10.10.1* or *10.10.10.1/index.html* in the address bar and enter

   * ``Username``: *admin*
   * ``Password``: *admin*

You may now set up the monitor on the configuration page according to the following instructions:

* To gather the information required for adding the monitor to the gams platform,
  see :ref:`monitors/dst/nano:Monitor Information`
* To connect the monitor to a WiFi network, see :ref:`monitors/dst/nano:WiFi Setup`
* To configure the monitor to send data directly to gams platform through **TCP**, see
  :ref:`monitors/dst/nano:TCP Setup`
* To configure the monitor to send data directly to gams platform through **MQTT**, see
  :ref:`monitors/dst/nano:MQTT Setup`
* To troubleshoot the monitor, see
  :ref:`monitors/dst/nano:Troubleshooting`

Do not opt to reboot the monitor after you save each change. Only after you've done all the configuration needed:

#. Click on ``Module Management`` on the left sidebar menu
#. Under the ``Module Reboot`` section, click on ``OK``

Monitor Information
-------------------

#. Click on ``Module Management`` on the left sidebar menu
#. Under the ``Version Information`` section:

   * Its **UUID** is on the ``Device SN`` line
   * If the ``Device SN`` line is not present, check the label on the monitor for its SN

WiFi Setup
----------

#. Click on ``Station Mode Setting`` on the left sidebar menu
#. Under the ``Station Parameter Setting`` section, click on ``scan`` to select the wireless network you wish to connect
   the monitor to or manually enter the ``SSID``
#. For ``Encryption Mode``:

   * If the WiFi network does not require a password, select *Disable* and click on ``save``
   * If the WiFi network requires a password, select *Enable*, enter the ``Password`` and click on ``save``

TCP Setup
----------

#. Click on ``Uart Setting`` on the left sidebar menu
#. Under section ``Uart Parameter Setting``, change ``Baud Rate`` to ``115200``

#. Click on ``Network Setting`` on the left sidebar menu
#. Under section ``Network Connection Setting``, change the following options:

   * ``Protocol``: *TCP Client*
   * ``Remote Port``: *8104*
   * ``Server Address``: *bridge.measureofquality.com*

MQTT Setup
----------

#. Click on ``Uart Setting`` on the left sidebar menu
#. Under section ``Uart Parameter Setting``, change ``Baud Rate`` to ``115200``

#. Click on ``Network Setting`` on the left sidebar menu
#. Under section ``Cloud Setting``, change the following options:

   * ``Cloud Host``: *bridge.measureofquality.com*
   * ``Cloud Port``: *1883*
   * ``Cloud Topic``: *dst/airsns/nano*

Troubleshooting
---------------

If you need to reset the monitor and activate its wireless hotspot again, follow step 2 in
:ref:`monitors/dst/nano:Configuration`.

If you need to troubleshoot the monitor, you can keep the monitor's wireless hotspot active even after configuration:

#. Click on ``Wifi Mode Select`` on the left sidebar menu
#. Select ``AP and Station`` and click on ``save``

.. note::
   You can change this setting only after finishing :ref:`monitors/dst/nano:WiFi Setup` and
   :ref:`monitors/dst/nano:TCP Setup` (or :ref:`monitors/dst/nano:MQTT Setup`).

After rebooting the monitor, you can connect to its wireless hotspot again and open its configuration page.

#. Click on ``Run State`` on the left sidebar menu

   * Its WiFi connection status is under the section ``STA State``
   * Its connection status to gams platform is under the section ``Network State``